Exhaust Drone Absorbing Pad
video
Exhaust Drone Absorbing Pad

Exhaust Drone Absorbing Pad

Under steady cruising or hard acceleration, a low resonant booming rises from the exhaust path and fills the cabin, the exhaust drone that ordinary flat insulation rarely targets. This absorbing pad occupies the dedicated acoustic zone near the exhaust path and underbody cavity: a lofty continuous-fiber layer lets that resonant energy enter the connected pores and dissipate, while a backed rigid formed layer holds shape and blocks transmission instead of letting sound reflect back into the cavity.

Product Description

 

Under steady cruising or hard acceleration, a low resonant booming rises from the exhaust path and fills the cabin, the exhaust drone that ordinary flat insulation rarely targets. This absorbing pad occupies the dedicated acoustic zone near the exhaust path and underbody cavity: a lofty continuous-fiber layer lets that resonant energy enter the connected pores and dissipate, while a backed rigid formed layer holds shape and blocks transmission instead of letting sound reflect back into the cavity. Built on single-material PET, the pad is graded to the specific drone source rather than cut from a catalog thickness, and it carries heat and flame-retardant options suited to zones close to exhaust hardware. Program teams turn to it when a vehicle suffers a persistent booming note that general insulation does not bring down, especially in hybrid and EV layouts where motor and exhaust resonance stands out against a quiet powertrain.

 

Drone problems are specific to one cavity and one exhaust path, so the pad is graded to that noise source rather than cut from a catalog thickness: balancing the soft-to-rigid ratio, basis weight (200-600 g/m2 lofty), and 10-30 mm loft to the actual frequency problem avoids adding acoustic mass where it is not needed. Because NRC depends on the rear air gap, trial samples validate the gap design before volume, and flame-retardant plus heat-deformation grades are matched to the underbody exposure level rather than applied generically.

 

Specifications

 

Parameter

Specification

Construction

Lofty acoustic felt backed by rigid formed felt layer; single-material PET

Lofty Layer Basis Weight

200-600 g/m2

Lofty Thickness

10-30 mm

Conventional PET : Low-Melt PET Ratio

75-85:15-25

Porosity

85%-98%

NRC

0.70-0.80 (20 mm + 50 mm gap); 0.75-0.90 (30 mm composite)

Airborne Sound Attenuation

25-35 dB (350 Hz - 10 kHz)

Long-Term Service Temperature

-40 C to +120 C; short-term 180 C for 30 min; heat-deformation at or above 120 C

Flame-Retardant Options

FMVSS 302, GB 8410, UL 94 HF-1/HB

Water Absorption

<=0.5% (<=0.1% after water-repellent treatment)

 

 

Applications

 

product-800-800

Underbody exhaust and drone zones: The lofty layer absorbs resonant cavity noise while the rigid face blocks transmission, and the -40 C to +120 C grade plus flame-retardant option handles heat near the exhaust path.

Electric-motor and inverter housings, trunk acoustic components: The soft felt layer dampens motor and cavity noise, and water-repellent treatment keeps performance where moisture can collect.

Battery thermal pads combined with aerogel or aluminum foil: The acoustic felt stacks with thermal layers where both noise and heat must be managed without dissimilar-material waste.

Customization

 

Basis weight (200-600 g/m2) and lofty thickness (10-30 mm); NRC grade set by thickness and rear air-gap design; water-repellent treatment; aluminum-foil or aerogel lamination; flame-retardant grade (FMVSS 302 / GB 8410 / UL 94 HF-1/HB); shaped cut components from rolls; OEM and ODM supported.
product-800-800

 

Packaging & Transportation

 

EXW terms with payment made in advance; packing per customer requirements, with carton or pallet options and protection against compression of the lofty layer. Specific carton dimensions, pallet configuration, and loading method are To Be Confirmed. Production photos or videos can be supplied during manufacture, and arrival damage is resolved by mutual negotiation.

 

 

FAQ

 

Q1: Do you accept third-party inspections?

A: Yes, third-party inspection is accepted.

Q2: What happens if the goods arrive damaged?

A: Damaged goods on arrival are resolved by mutual negotiation.

Q3: Will I receive regular updates (photos/videos) during production?

A: Yes, production photos or videos are supplied during manufacture.

 

Hot Tags: exhaust drone absorbing pad, China exhaust drone absorbing pad manufacturers, suppliers, factory, PET continuous filament backing, pet continuous filament nonwovens, PET Filament Acoustic Felt, PET spunbond filtration material, polyester continuous filament nonwoven, recycled PET filament nonwoven

Send Inquiry