Cabin Sound Insulation Lining
video
Cabin Sound Insulation Lining

Cabin Sound Insulation Lining

Built from a PET and low-melting-point polyester blend bonded without solvent adhesive, the cabin sound insulation lining is a soft, lofty layer distributed through the interior cavities - pillar fills, dash-side pockets, door trim spaces, and rear-quarter areas - to raise the overall quietness of the passenger compartment rather than treating a single panel. It absorbs mid-frequency resonance that builds up inside closed trim gaps and softens road, wind, and panel noise before it reaches occupants, while springing back after assembly squeeze so the trim never feels padded flat.

Product Description

 

Built from a PET and low-melting-point polyester blend bonded without solvent adhesive, the cabin sound insulation lining is a soft, lofty layer distributed through the interior cavities - pillar fills, dash-side pockets, door trim spaces, and rear-quarter areas - to raise the overall quietness of the passenger compartment rather than treating a single panel. It absorbs mid-frequency resonance that builds up inside closed trim gaps and softens road, wind, and panel noise before it reaches occupants, while springing back after assembly squeeze so the trim never feels padded flat. Lightweight and glass-fiber-free, it adds comfort without heavy deadening, and buyers use it to balance noise control against vehicle weight across the whole cabin instead of over-filling one area; each cavity can be tuned to its own volume rather than cut from one generic roll.

 

Across a cabin, one blanket density wastes weight in quiet pockets and under-performs in resonating cavities. Haokai tunes each lining station's fiber ratio, basis weight (200-1,200 g/m²), and unequal-thickness zones to the specific cavity instead of running one generic fill, then holds that tuned layup repeatably through batch production. This consistency matters for OEM buyers who need identical absorption and trim fit across thousands of vehicles rather than a one-off sample that drifts as volume grows.

 

Specifications

 

Parameter

Specification

Material

PET + LMPET blend (conventional PET : LMPET = 75-85:15-25)

Raw-felt basis weight

200-1,200 g/m²

Finished density

0.02-0.15 g/cm³

Finished thickness

5-40 mm

Porosity

70%-95%

Compression recovery

≥70%; typical automotive grades ≥80%

Thermal conductivity

0.032-0.045 W/(m·K)

LMPET melting point

110-180 °C (110/130 °C common)

Formaldehyde / odor

≤15 µg/(m²·h) / ≤3.5

Compliance

RoHS / REACH / ELV / GB 30512; glass-fiber-free

 

 

Applications

 

product-800-800

A/B/C pillar and dash-side cavity fills: The lofty layer follows curved trim and recovers after assembly compression, absorbing mid-frequency cavity resonance that a flat filler would leave as gap-borne rattle.

Door trim inner acoustic liner: The porous structure absorbs road and wind noise behind the door panel, and the 0.032-0.045 W/(m·K) conductivity adds a light thermal buffer against the cold door skin.

Rear-quarter and stowage-space fills: System-specific weight and layup match each pocket's volume, so quiet zones are not over-built with unnecessary felt weight.

Customization

 

  • Fiber ratio and fiber type (conventional, hollow, microfine PET)
  • Basis weight, finished thickness, local density, and unequal-thickness zones
  • 3D thermoform mold shape to pillar, dash, and door curves; holes and clearance areas
  • Laminated visible surface; OEM/ODM from customer drawings or prototypes
product-800-800

 

Packaging & Transportation

 

Parts ship EXW from the Rugao, Jiangsu facility after packing; prepayment applies, with RMB and related currencies accepted. Packing is arranged per customer requirements using cartons, pallets, separators, or supports that protect soft formed layers from crushing during stacking; export packing details are confirmed per project. FOB, CIF, and DDP are not offered.

 

 

FAQ

 

Q1: Can you provide a prototype/sample before mass production?

A: Yes, samples can be provided before mass production, and custom parts can be laser-cut.

Q2: How do you control product quality?

A: Production follows IATF 16949 quality control; every finished part receives 100% inspection before packing and third-party inspection is accepted.

Q3: Can I mix different colors or models in one MOQ order?

A: Yes, different colors or models can be mixed within one MOQ order.

 

Hot Tags: cabin sound insulation lining, China cabin sound insulation lining manufacturers, suppliers, factory, automotive center console components, automotive floor covering components, PET felt forming sheets, PET felt thermoformed interior panels, PET Molded Automotive Felt, vehicle interior composite components

Send Inquiry